By: Jeff Axel, EAA 1058953
This piece originally ran in the September 2026 issue of EAA Sport Aviation magazine.
My wife, Sandy, said I needed a retirement project, so, as a lark, I said, “Why don’t we go to Sebring and check out the AirCam?” After a ride, with Phil Lockwood flying, she got out and said, “We have gotta get us one of THESE!” We ordered the kit and then raced home to organize our three-car garage as an aircraft workshop.
On December 10, 2023, two huge crates arrived, and with the help of our good friend Stu Luxenberg, his skillset, and his forklift, the crates were moved into our garage. A week later we completed the inventory of thousands of parts and 16,000 rivets! After the reality of the situation set in, work began. That first winter was lots of match drilling and upsizing and deburring thousands of holes. I got into a routine and tried to spend at least some time every day working on the airplane and improving my knowledge and techniques.
I would not have proceeded without the help of a good friend, Dirk Wittig, a recently retired A&P/IA mechanic. EAA chapters were invaluable, too, with an EAA technical counselor, Ernie Moreno, EAA 276279, from Chapter 292 inspecting and advising us at various points.
The challenge of priming and painting was solved when my friend Stu suggested his friend Justin Becker could help. Indeed, he did, and not only with painting but also with some electrical work. I borrowed Stu’s inflatable paint booth and later purchased a larger one for painting the fuselage and wings. (All the neighborhood kids thought they were bouncy houses and were disappointed that they couldn’t play in them.) Having the ability to prime and paint parts and later the entire airplane in my driveway saved all sorts of time.
Those 16,000 rivets had to go somewhere. This all took time, but I made one strategic error — one day Sandy asked to try her hand at riveting, and I almost didn’t get the pneumatic riveter back! Who knew she would like this sort of thing? We began to call our AirCam Zoey since that name was on several parts as part of a matching system used at Lockwood when putting parts on the jig used to assemble and tack-rivet the airframe together before shipping. Once the holes in the fuselage were match drilled and Clecoed together, the rivets Lockwood used were drilled out and those holes match drilled as well. The fuselage was then disassembled prior to priming.
When it came time to do the fabric work, Sandy and I had concerns since neither of us had any experience, but we worked through those after reading the Poly Fiber manual. We got into a rhythm of using Poly-Tak, heat shrinking, and then applying Poly-Brush and taping the control surfaces. We finished priming the metal parts and applying Poly-Brush to fabric parts just as the weather turned colder and we had to move back inside for the winter.
By the time spring rolled around again we were running out of rivets, and the parts were assembled and ready for final painting. Lots of discussion ensued as to a paint design, but we finally landed on a bright red base with gray and black striping. Justin and I suffered through the hot days of summer in the paint booth, but Zoey’s red dress looked pretty good at the end. By August, we had to move Zoey to the airport, as she had gotten too big for the garage. At the airport, wings and tail surfaces were attached, and then it was time to work on avionics and airframe wiring.
Neither Dirk nor I had any experience with Rotax engines so we went to Lockwood headquarters to take a course on maintenance and inspection. When we got back, we mounted the engines and I completed the wiring. Once a couple of issues were sorted out, the props were assembled and we were ready to run the engines, and our initial runs went off without incident. While getting ready to install the emergency locator transmitter (ELT), Dan Benua, EAA 454466, a hangar neighbor and technical counselor for EAA Chapter 105, stopped by. I was assembling a connector that required soldering several wires to its pins. Dan felt that a connector with crimped pins would be easier. I didn’t have one — the pins, the crimper, or the wires. Dan ran home and returned 20 minutes later with the materials, and 15 minutes later my ELT wiring was complete. EAA at its best!
With fuel flow checks, engine runs, and taxi tests, after 25 months and almost 1,900 hours, we were ready for the FAA inspection and first flight. Designated Airworthiness Representative Gary Brown inspected the airplane and issued our airworthiness certificate. I am a low-time tailwheel pilot and had only a dozen or so landings in an AirCam, so Gary suggested I reach out to Robin Reid, EAA 99931, to do the initial test flight. I was frankly relieved to have someone with a lot of experience to do this, and Robin agreed. The weather was dry and clear, unusual for Portland in February, but it worked to our advantage, and the first flight went off without a hitch with Robin flying and me in the middle seat. Robin described the flight as “pleasantly boring.” After the flight and a thorough inspection, Robin and I switched seats, and I finally got to fly my airplane. I was amazed it flew so well.
Robin and I flew off the EAA flight test cards over the next five days. I’m still getting used to the sight picture while landing this nimble taildragger, but Sandy and I agree that it was well worth the investment of time, money, and brain cells to “get us one of THESE!” Now, once I get more experience perfecting my landings, we’re off to make some bucket list trips, but more importantly, to take young people for rides to introduce them to the wonders of low-and-slow flight. Let the adventures begin!
Attention — Aircraft Builders and Restorers
We would love to share your story with your fellow EAA members in the pages of EAA Sport Aviation magazine, even if it’s a project that’s been completed for a while. Readers consistently rate the “What Our Members Are Building/Restoring” section of the magazine as one of their favorites, so don’t miss the chance to show off your handiwork and inspire your peers to start or complete projects of their own. Learn more ->











